Mô tả ngắn gọn
Communication module | 1x RS232 or 1x RS485/RS422, 2 digital inputs, 2 digital channels configurable as inputs or outputs using software |
Thông tin chung
Insulation voltage between channel and bus | 500 Veff |
B&R ID code | 0xA90F |
Nguồn điện cảm biến/bộ truyền động | 0.5 A summation current |
Chỉ số trạng thái | RS232, RS485/RS422, I/O function per channel, supply voltage, bus function |
Chẩn đoán | |
Đầu ra | Yes, using LED status indicator and software |
I/O power supply | Yes, using LED status indicator and software |
RS232 | Yes, using LED status indicator |
RS485/RS422 | Yes, using LED status indicator |
Connection type | |
X2X Link | M12, B-coded |
Giao diện and inputs/outputs | 4x M12, A-coded |
I/O power supply | M8, 4-pin |
Tiêu thụ điện năng | |
Internal I/O | 2.4 W |
X2X Link power supply | 0.75 W |
Chứng nhận | |
CE | Yes |
UKCA | Yes |
ATEX |
Zone 2, II 3G Ex nA IIA T5 Gc IP67, Ta = 0 – Max. 60°C TÜV 05 ATEX 7201X |
UL |
cULus E115267 Thiết bị điều khiển công nghiệp |
HazLoc |
cCSAus 244665 Process control equipment for hazardous locations Class I, Division 2, Groups ABCD, T5 |
KC | Yes |
Giao diện
Interface IF1 | |
Signal | RS232 |
Max. distance | 900 m |
Tỷ lệ chuyển nhượng | Max. 115.2 kbit/s |
FIFO buffer | Phần mềm |
Handshake lines | No |
Interface IF2 | |
Signal | RS485/RS422 |
Max. distance | 1200 m |
Tỷ lệ chuyển nhượng | Max. 115.2 kbit/s |
FIFO buffer | Phần mềm |
Terminating resistor | Integrated in module |
I/O power supply
Điện áp danh định | 24 VDC |
Điện áp range | 18 to 30 VDC |
Integrated protection | Reverse polarity protection |
Tiêu thụ điện năng | |
Nguồn điện cảm biến/bộ truyền động | Max. 12 W |
Nguồn điện cảm biến/bộ truyền động
Điện áp | I/O power supply minus voltage drop for short-circuit protection |
Giảm điện áp để bảo vệ ngắn mạch tại 0.5 A | Max. 2 VDC |
Summation current | Max. 0.5 A |
Chống đoản mạch | Yes |
Đầu vào kỹ thuật số
Số lượng | Up to 4 if the 2 digital channels are used as digital inputs |
Điện áp danh định | 24 VDC |
Input characteristics per EN 61131-2 | Kiểu 1 |
Điện áp đầu vào | 18 to 30 VDC |
Dòng điện đầu vào tại 24 VDC | Typ. 3.5 mA |
Mạch đầu vào | Sink |
Bộ lọc đầu vào | |
Phần cứng | ≤100 µs |
Phần mềm | Default 0 ms, configurable between 0 and 25 ms in 0.2 ms intervals |
Điện trở đầu vào | Typ. 6.67 kΩ |
Ngưỡng chuyển đổi | |
Low | <5 V |
High | >15 VDC |
Digital outputs
Số lượng | Up to 2 if the 2 digital channels are used as digital outputs |
Khác nhau | Dòng điện-sourcing FET |
Điện áp danh định | 24 VDC |
Điện áp chuyển mạch | I/O power supply minus residual voltage |
Dòng điện đầu ra danh nghĩa | 0.5 A |
Tổng dòng điện danh định | 1 A |
Mạch đầu ra | Source |
Bảo vệ đầu ra | Thermal shutdown in the event of overcurrent or short circuit, integrated protection for switching inductive loads, reverse polarity protection of the output power supply |
Diagnostic status | Output monitoring with 10 ms delay |
Leakage current when the output is switched off | <120 μA |
Dòng điện ngắn mạch cực đại | <2.1 A |
Bật trong trường hợp quá tải hoặc ngắn mạch | Approx. 1 ms (depends on the module temperature) |
Độ trễ chuyển đổi | |
0 → 1 | <100 μs |
1 → 0 | <150 μs |
Tần số chuyển đổi | |
Resistive load | Max. 1000 Hz |
Inductive load | See section “Switching inductive loads”. |
Braking voltage when switching off inductive loads | Typ. 68 VDC |
Tính chất điện
Cách ly điện |
Bus isolated from channel and IF
Channel not isolated from channel and IF
|
Điều kiện hoạt động
Hướng lắp đặt | |
Any | Yes |
Độ cao lắp đặt so với mực nước biển | |
0 to 2000 m | Không có giới hạn |
>2000 m | Reduction of ambient temperature by 0.5°C per 100 m |
Mức độ bảo vệ mỗi EN 60529 | IP67 |
Điều kiện môi trường xung quanh
Nhiệt độ | |
Hoạt động | -25 to 60°C |
Giảm tải | – |
Lưu trữ | -40 to 85°C |
Transport | -40 to 85°C |
Tính chất cơ học
Dimensions | |
Width | 53 mm |
Height | 85 mm |
Depth | 42 mm |
Weight | 195 g |
Torque for connections | |
M8 | Max. 0.4 Nm |
M12 | Max. 0.6 Nm |