Bộ lập trình X20cCP1382-RT
Thông số kỹ thuật bộ lập trình B&R X20cCP1382-RT
đại lý X20cCP1382-RT | nhà phân phối X20cCP1382-RT | đại lý B&R | B&R Việt Nam
Mô tả ngắn gọn
| Giao diện | 1x RS232, 1x Ethernet, 1x POWERLINK, 2x USB, 1x X2X Link, 1x CAN bus |
| Mô-đun hệ thống | Bộ điều khiển B&R |
Thông tin chung
| B&R ID code | 0xE707 |
| Làm mát | Fanless |
| Chỉ số trạng thái | CPU function, Ethernet, POWERLINK, RS232, CAN bus, CAN bus terminating resistor, PLC power supply, I/O power supply, I/O function per channel |
| Chẩn đoán | |
| Outputs | Digital outputs: Yes, using LED status indicator and software (output error status) |
| CPU function | Yes, using LED status indicator |
| CAN bus data transfer | Yes, using LED status indicator |
| RS232 data transfer | Yes, using LED status indicator |
| Inputs | Analog inputs: Yes, using LED status indicator and software |
| Ethernet | Yes, using LED status indicator |
| I/O power supply | Yes, using LED status indicator |
| POWERLINK | Yes, using LED status indicator |
| Supply voltage monitoring | Yes, using LED status indicator |
| Nhiệt độ | Yes, using software register |
| Terminating resistor | Yes, using LED status indicator |
| Hỗ trợ | |
| Bộ điều khiển B&R redundancy | No |
| ACOPOS support | Yes |
| reACTION-capable I/O channels | Yes |
| Hỗ trợ thành phần trực quan | Yes |
| Tiêu thụ điện năng without interface module and USB | 5.8 W |
| Tiêu thụ điện năng for X2X Link power supply | 0.8 W |
| Tiêu thụ điện năng | |
| Internal I/O | 2.3 W |
| Tiêu tán công suất bổ sung do bộ truyền động gây ra (resistive) [W] | – |
| Kiểu of signal lines | Shielded lines must be used for all high-speed digital inputs/outputs, line length: Max. 20 m |
| Chứng nhận | |
| CE | Yes |
| UKCA | Yes |
| ATEX |
Zone 2, II 3G Ex nA nC IIA T5 Gc IP20, Ta (see X20 user’s manual) FTZÚ 09 ATEX 0083X |
| UL |
cULus E115267 Industrial control equipment |
| HazLoc |
cCSAus 244665 Process control equipment for hazardous locations Class I, Division 2, Groups ABCD, T5 |
| DNV |
Nhiệt độ: B (0 to 55°C) Humidity: B (up to 100%) Vibration: B (4 g) EMC: B (bridge and open deck) |
| LR | ENV1 |
| KR | Yes |
| ABS | Yes |
| BV | EC33B Nhiệt độ: 5 – 55°C Vibration: 4 g EMC: Bridge and open deck |
CPU and X2X Link power supply
| Input voltage | 24 VDC -15% / +20% |
| Input current | Max. 1 A |
| Fuse | Integrated, cannot be replaced |
| Reverse polarity protection | Yes |
X2X Link power supply output
| Nominal output power | 2 W |
| Parallel connection | Yes |
| Redundant operation | Yes |
Input I/O power supply
| Input voltage | 24 VDC -15% / +20% |
| Fuse | Required line fuse: Max. 10 A, slow-blow |
Output I/O power supply
| Nominal output voltage | 24 VDC |
| Permissible contact load | 10 A |
Bộ điều khiển B&R
| Đồng hồ thời gian thực | Retention for at least 300 hours, typ. 1000 hours at 25°C, 1 s resolution, -18 to 28 ppm accuracy at 25°C |
| FPU | Yes |
| Bộ xử lý | |
| Kiểu | Vx86EX |
| Tần số đồng hồ | 400 MHz |
| L1 cache | |
| Mã dữ liệu | 16 kB |
| Mã chương trình | 16 kB |
| L2 cache | 128 kB |
| Bộ xử lý I/O tích hợp | Processes I/O data points in the background |
| Modular interface slots | 1 |
| Các biến số | 32 kB FRAM, retention >10 years |
| Thời gian chu kỳ lớp nhiệm vụ ngắn nhất | 1 ms |
| Thời gian chu kỳ hướng dẫn điển hình | 0.0199 µs |
| Bộ nhớ chuẩn | |
| RAM | 256 MB DDR3 SDRAM |
| Bộ nhớ ứng dụng | |
| Kiểu | 2 GB eMMC flash memory |
| Lưu giữ dữ liệu | 10 years |
| Lượng dữ liệu có thể ghi | |
| Đảm bảo | 40 TB |
| Kết quả trong 5 năm | 21.9 GB/day |
| Đảm bảo erase/write cycles | 20,000 |
| Mã sửa lỗi (ECC) | Yes |
Giao diện
| Interface IF1 | |
| Signal | RS232 |
| Khác nhau | Connection via 16-pin terminal block X20TB1F |
| Max. distance | 900 m |
| Tỷ lệ chuyển nhượng | Max. 115.2 kbit/s |
| Interface IF2 | |
| Signal | Ethernet |
| Khác nhau | 1x RJ45 shielded |
| Chiều dài dòng | Max. 100 m between 2 stations (segment length) |
| Tỷ lệ chuyển nhượng | 10/100 Mbit/s |
| Transfer | |
| Lớp vật lý | 10BASE-T/100BASE-TX |
| Half-duplex | Yes |
| Full-duplex | Yes |
| Autonegotiation | Yes |
| Auto-MDI/MDIX | Yes |
| Interface IF3 | |
| Fieldbus | POWERLINK managing or controlled node |
| Kiểu | Kiểu 4 |
| Khác nhau | 1x RJ45 shielded |
| Chiều dài dòng | Max. 100 m between 2 stations (segment length) |
| Tỷ lệ chuyển nhượng | 100 Mbit/s |
| Transfer | |
| Lớp vật lý | 100BASE-TX |
| Half-duplex | Yes |
| Full-duplex | POWERLINK mode: No / Ethernet mode: Yes |
| Autonegotiation | Yes |
| Auto-MDI/MDIX | Yes |
| Interface IF4 | |
| Kiểu | USB 1.1/2.0 |
| Khác nhau | Kiểu A |
| Max. output current | 0.5 A |
| Interface IF5 | |
| Kiểu | USB 1.1/2.0 |
| Khác nhau | Kiểu A |
| Max. output current | 0.1 A |
| Interface IF6 | |
| Fieldbus | X2X Link master |
| Interface IF7 | |
| Signal | CAN bus |
| Khác nhau | Connection via 16-pin terminal block X20TB1F |
| Max. distance | 1000 m |
| Tỷ lệ chuyển nhượng | Max. 1 Mbit/s |
| Terminating resistor | Integrated in module |
| Bộ điều khiển B&R | SJA 1000 |
Digital inputs
| Quantity | 14 standard inputs, 4 high-speed inputs and 4 mixed channels, configuration as input or output using software |
| Nominal voltage | 24 VDC |
| Input voltage | 24 VDC -15% / +20% |
| Input current at 24 VDC |
X1 – Standard inputs: Typ. 3.5 mA X2 – Standard inputs: Typ. 2.68 mA X2 – High-speed inputs: Typ. 3.5 mA X3 – Mixed channels: Typ. 2.68 mA |
| Input circuit | Sink |
| Input filter | |
| Hardware |
Standard inputs and mixed channels: ≤200 μs High-speed inputs: ≤2 μs, when used as standard inputs: ≤200 μs |
| Software | Default 1 ms, configurable between 0 and 25 ms in 0.1 ms increments |
| Connection type | 1-wire connections |
| Input resistance |
X1 – Standard inputs: 6.8 kΩ X2 – Standard inputs: 8.9 kΩ X2 – High-speed inputs: 6.8 kΩ X3 – Mixed channels: 8.9 kΩ |
| Additional functions |
X2 – High-speed digital inputs: 2x 250 kHz event counting, 2x AB counter, ABR incremental encoder, direction/frequency, period measurement, gate measurement, differential time measurement, edge counters, edge times |
| Switching threshold | |
| Low | <5 VDC |
| High | >15 VDC |
AB incremental encoder
| Quantity | 2 |
| Encoder inputs | 24 V, asymmetrical |
| Counter size | 32-bit |
| Input frequency | Max. 100 kHz |
| Evaluation | 4x |
| Encoder power supply | Module-internal, max. 300 mA |
| Overload characteristics of encoder power supply | Short-circuit proof, overload-proof |
ABR incremental encoder
| Quantity | 1 |
| Encoder inputs | 24 V, asymmetrical |
| Counter size | 32-bit |
| Input frequency | Max. 100 kHz |
| Evaluation | 4x |
| Encoder power supply | Module-internal, max. 300 mA |
| Overload characteristics of encoder power supply | Short-circuit proof, overload-proof |
Event counters
| Quantity | 2 |
| Signal form | Square wave pulse |
| Evaluation | 1x |
| Input frequency | Max. 250 kHz |
| Counter frequency | 250 kHz |
| Counter size | 32-bit |
Edge detection / Time measurement
| Possible measurements | Period measurement, gate measurement, differential time measurement, edge counter, edge times |
| Measurements per module | Each function up to 2x |
| Signal form | Square wave pulse |
| Counter size | 32-bit |
| Input frequency | Max. 10 kHz |
| Timestamp | 1 µs resolution |
Analog inputs
| Input | ±10 V or 0 to 20 mA / 4 to 20 mA, via different terminal connections |
| Input type | Differential input |
| Digital converter resolution | |
| Voltage | ±12-bit |
| Current | 12-bit |
| Conversion time |
1 channel enabled: 100 µs 2 channels enabled: 200 µs |
| Output format | |
| Data type | INT |
| Voltage | INT 0x8001 – 0x7FFF / 1 LSB = 0x0008 = 2.441 mV |
| Current | INT 0x0000 – 0x7FFF / 1 LSB = 0x0008 = 4.883 μA |
| Input impedance in signal range | |
| Voltage | 20 MΩ |
| Current | – |
| Load | |
| Voltage | – |
| Current | <300 Ω |
| Input protection | Protection against wiring with supply voltage |
| Permissible input signal | |
| Voltage | Max. ±30 V |
| Current | Max. ±50 mA |
| Output of digital value during overload | Configurable |
| Conversion procedure | SAR |
| Input filter | Third-order low-pass filter / Cutoff frequency 1 kHz |
| Max. error | |
| Voltage | |
| Gain | 0.18% (Rev. <C0: 0.37%) |
| Offset | 0.04% (Rev. <C0: 0.25%) |
| Current | |
| Gain | 0 to 20 mA = 0.15% (Rev. <C0: 0.52%) / 4 to 20 mA = 0.25% |
| Offset | 0 to 20 mA = 0.1% (Rev. <C0: 0.4%) / 4 to 20 mA = 0.15% |
| Max. gain drift | |
| Voltage | 0.017 %/°C |
| Current | 0 to 20 mA = 0.015 %/°C / 4 to 20 mA = 0.023 %/°C |
| Max. offset drift | |
| Voltage | 0.008 %/°C |
| Current | 0 to 20 mA = 0.008 %/°C / 4 to 20 mA = 0.012 %/°C |
| Common-mode rejection | |
| DC | 70 dB |
| 50 Hz | 70 dB |
| Common-mode range | ±12 V |
| Crosstalk between channels | <-70 dB |
| Nonlinearity | |
| Voltage | <0.025% |
| Current | <0.05% |
Resistance measurement temperature inputs
| Quantity | 1 |
| Input | Resistance measurement with constant current supply for 2-wire connections |
| Digital converter resolution | 13-bit |
| Conversion time |
Only temperature input enabled: 200 µs Nhiệt độ and analog input enabled: 400 µs |
| Conversion procedure | SAR |
| Output format | INT or UINT for resistance measurement |
| Sensor | |
| Pt1000 | -200 to 850°C |
| Resistance measurement range | 0.1 to 4000 Ω |
| Nhiệt độ sensor resolution | 1 LSB = 0x0005 = 0.16°C |
| Resistance measurement resolution | 1 LSB = 0x0005 = 0.49 Ω |
| Input filter | First-order low-pass filter / cutoff frequency 7 Hz |
| Sensor standard | EN 60751 |
| Common-mode range | 1 V |
| Linearization method | Internal |
| Measurement current | 1 mA |
| Permissible input signal | Short-term max. ±30 V |
| Max. error at 25°C | |
| Gain | 0.3% (Rev. <C0: 1.93%) |
| Offset | 0.15% (Rev. <C0: 0.32%) |
| Max. gain drift | 0.023 %/°C |
| Max. offset drift | 0.012%/°C |
| Nonlinearity | <0.05% |
| Standardized range of values for resistance measurement | 0.1 to 4000.0 Ω |
| Crosstalk between channels | <-70 dB |
| Common-mode rejection | |
| 50 Hz | >60 dB |
| DC | – |
| Nhiệt độ sensor normalization | |
| Pt1000 | -200 to 850°C |
Digital outputs
| Quantity | 4 standard outputs, 4 high-speed outputs and 4 mixed channels, configuration as input or output using software |
| Khác nhau |
Standard outputs and mixed channels: Current-sourcing FET High-speed outputs: Push-Pull |
| Nominal voltage | 24 VDC |
| Switching voltage | 24 VDC -15% / +20% |
| Nominal output current |
Standard outputs and mixed channels: 0.5 A High-speed outputs: 0.2 A |
| Total nominal current |
Standard outputs and mixed channels: 4 A High-speed outputs: 0.8 A |
| Connection type | 1-wire connections |
| Output circuit |
Standard outputs and mixed channels: Source High-speed outputs: Sink or source |
| Output protection |
Thermal shutdown in the event of overcurrent or short circuit (see value “Short-circuit peak current”) Internal freewheeling diode for switching inductive loads (see section “Switching inductive loads”) |
| Pulse width modulation | |
| Period duration | 5 to 65535 µs corresponds to 200 kHz to 15 Hz |
| Pulse duration | 0 to 100%, minimum 2.5 µs |
| Resolution for pulse duration | 0.1% of the configured frequency |
| Diagnostic status |
Standard outputs and mixed channels: Output monitoring with 10 ms delay High-speed outputs: Output monitoring with 10 µs delay |
| Leakage current when the output is switched off |
Standard outputs and mixed channels: 5 µA High-speed outputs: 25 µA |
| RDS(on) | 140 mΩ |
| Residual voltage |
Standard outputs and mixed channels: <0.1 V at nominal current 0.5 A High-speed outputs: <0.9 V at nominal current 0.1 A |
| Peak short-circuit current |
Standard outputs and mixed channels: <3 A High-speed outputs: <20 A |
| Switch-on in the event of overload shutdown or short-circuit shutdown |
Standard outputs and mixed channels: Approx. 10 ms (depends on module temperature) High-speed outputs: No switch-on |
| Switching delay | |
| 0 → 1 |
Standard outputs and mixed channels: <300 µs High-speed outputs: <3 µs |
| 1 → 0 |
Standard outputs and mixed channels: <300 µs High-speed outputs: <3 µs |
| Switching frequency | |
| Resistive load |
Standard outputs and mixed channels: Max. 500 Hz High-speed outputs: 50 kHz, max. 200 kHz (see section “Switching frequency derating for high-speed digital outputs”) |
| Inductive load | See section “Switching inductive loads”. |
| Braking voltage when switching off inductive loads | Standard outputs and mixed channels: Typ. 45 VDC |
Tính chất điện
| Cách ly điện |
Ethernet (IF2), POWERLINK (IF3) and X2X (IF6) isolated from each other, from other interfaces and from PLC Channel isolated from bus Channel not isolated from channel or PLC |
Điều kiện hoạt động
| Hướng lắp đặt | |
| Nằm ngang | Yes |
| Thẳng đứng | Yes |
| Độ cao lắp đặt so với mực nước biển | |
| 0 to 2000 m | Không có giới hạn |
| >2000 m | Reduction of ambient temperature by 0.5°C per 100 m |
| Mức độ bảo vệ mỗi EN 60529 | IP20 |
Điều kiện môi trường xung quanh
| Nhiệt độ | |
| Hoạt động | |
| Nằm ngang mounting orientation | -25 to 60°C |
| Thẳng đứng mounting orientation | -25 to 50°C |
| Giảm tải | See section “Switching frequency derating for high-speed digital outputs”. |
| Lưu trữ | -40 to 85°C |
| Transport | -40 to 85°C |
| Độ ẩm tương đối | |
| Hoạt động | Up to 100%, condensing |
| Lưu trữ | 5 to 95%, non-condensing |
| Transport | 5 to 95%, non-condensing |
Tính chất cơ học
| Note |
X20 end cover plate (right) included in delivery 3 X20 terminal blocks (16-pin) included in delivery Interface module slot cover included in delivery |
| Dimensions | |
| Width | 164 mm |
| Height | 99 mm |
| Depth | 75 mm |
| Weight | 310 g |
Brand
B&R
Sản phẩm tương tự
Bộ lập trình
Bộ lập trình
Bộ lập trình
Bộ lập trình
Bộ lập trình
Bộ lập trình
Bộ lập trình
Bộ lập trình